21 May 2013 10:26:26
Latest News
First Time Visitor
Login
Register
There are 7 Guest users online.
Products
Emulation Tools
8xC51 Family
LPC76x Family
8xC51MX Family
LPC900 Family
Choosing an
Emulator
Programmers
Adapters
Bondouts/Spares
Repairs
Microcontroller Sales
Ordering
Show My Cart
Proceed to Checkout
Support
Downloads
Forums
Links and Resources
Data Sheets
Technical Notes
Testimonials
FAQ
Common Problems
Repairs and Returns
Contacting Us
About Acqura
Take our Poll
|
|
|
|
|
|
|
Datasheet |
|
|
P89LPC904 8-bit microcontroller Datasheet |
|
A summary of the datasheet is shown below. Get the full datasheet as a PDF. 
The P89LPC904 has byte-erasable Flash memory, ADC, enhanced timing functions and on-chip serial communications. It is based on a high performance processor architecture that executes instructions in two to four clocks, six times the rate of standard 80C51 devices. Many system-level functions have been incorporated into this family in order to reduce component count, board space, and system cost.
Principal Features
-1 kB Flash code memory organised into 256-byte sectors, 16-byte pages and single byte erase functionality.
-128-byte RAM data memory.
-Two 16-bit counter/timers.
-23-bit system timer that can be used as a RTC (Real-Time Clock)
-Two input multiplexed 8-bit A/D converter/single DAC output.
-Two analog comparators with selectable inputs and reference source.
-Enhanced UART with fractional baud rate generator, break detect, framing error detection, automatic address detection and versatile interrupt capabilities.
-High-accuracy internal RC oscillator option, factory calibrated to 1 %, allows operation without external oscillator components. The RC oscillator option is selectable and fine tunable.
-VDD operating range of 2.4 V to 3.6 V with 5 V tolerant I/O pins (may be pulled up or driven to 5.5 V).
-Up to six I/O pins when using internal oscillator and reset options.
-A variety of package options ranging from low profile 8-, 14-, and 16-pin TSSOP up to 28-pin HVQFN packages.
Additional Features
-A high performance 80C51 CPU provides instruction cycle times of 136 ns to 272 ns for all instructions except multiply and divide when using the internal 7.3728 MHz RC oscillator. A lower clock frequency for the same performance results in power savings and reduced EMI.
-In-Application Programming (IAP-Lite) and byte erase allows code memory to be used for non-volatile data storage.
-Serial Flash ICP allows simple production coding with commercial EPROM programmers. Flash security bits prevent reading of sensitive application programs.
-Watchdog timer with separate on-chip oscillator, requiring no external components. The watchdog prescaler is selectable from 8 values.
-Low voltage reset (Brownout detect) allows a graceful system shutdown when power fails. May optionally be configured as an interrupt.
-Idle and two different Power-down reduced power modes. Improved wake-up from Power-down mode (a low interrupt input starts execution). Typical Power-down current is less than 1 uA (total Power-down with voltage comparators disabled).
-Active-LOW reset. On-chip power-on reset allows operation without external reset components. A reset counter and reset glitch suppression circuitry prevent spurious and incomplete resets. A software reset function is also available.
-Configurable on-chip oscillator with frequency range options selected by user programmed Flash configuration bits. The external clock support frequencies from 20kHz to the maximum operating frequency of 12MHz.
-Programmable port output configuration options:
- quasi-bidirectional
- open drain
- push-pull
- input-only
-Port ‘input pattern match’ detect. Port 0 may generate an interrupt when the value of the pins match or do not match a programmable pattern.
-LED drive capability (20 mA) on all port pins. A maximum limit is specified for the entire chip.
-Controlled slew rate port outputs to reduce EMI. Outputs have approximately 10 ns minimum ramp times.
-Only power and ground connections are required to operate the device when on-chip oscillator and reset options are selected.
-Four interrupt priority levels.
-One keypad interrupt input.
-Second data pointer.
-Schmitt trigger port inputs.
-Emulation support with Philips PDS900.
See the full datasheet as a PDF
|
|
|
|
|
|
|
|
|
|
|
|